DB45 How to: I have connected DB45 to my LAN. How can I access the device?
DB45 has an assigned Static IP address. In order to establish a communication with the device, your PC should be connected to the same Subnetwork as DB45. For further information, please refer to the Quick User Guide .
DB45 How to: I cannot receive SMS from the monitoring equipment. How can I configure the GSM modem?
First, you will have to make sure that the GSM modem is properly connected to the device. Then enter the device via the WEB Interface and go to Settings > Comm > GSM Modem section. Check the baud rate, as it is mandatory for the proper operation of the GSM Modem. You will also have to make sure that the PIN security of the used SIM card is disabled.
If the above conditions are fulfilled you could proceed with the next step. Up to four numbers for SMS alarm notifications could be set. We recommend a test SMS to be generated (via pressing the ‘Test’ button), once all needed settings are applied. Upon success, the SMS will be delivered to all specified GSM numbers.
Example of Test SMS Message:
DB45 Test Message.The current condition of the GSM Modem could be checked in the “Status Screen”.
DB45 How to: I cannot receive E-mails from the monitoring equipment. How can I configure the E-mail client?
The unit should be configured according to the e-mail provider’s specifications. Otherwise, messages to your e-mail account will not be received. The configuration is made through the WEB Interface, Settings > E-mail section.
Enter the desired alarm recipients in e-mail 1 and/or e-mail 2 fields. Fill in your e-mail account settings: Sender, Username and Password, Server, SMTP port and connection type. You can also change the host name if necessary or otherwise leave it as it is.
We recommend you to use the ‘Test’ button and generate a test e-mail, which upon success will be delivered to the specified E-mail 1 and/or E-mail 2.
Example of Test E-mail Message:
DB45 Test Message.
Please do not reply to this e-mail.Note that the “Network” section should also be correctly configured, most importantly the “DNS” parameter if you want to use server names (ex: “smtp.yourdomain.com”).
DB45 How to: I do not hear the audio from the ‘Listen’ button of the WEB Interface.
Please verify that your speakers/headphones are connected and the audio is not muted. Also, there is some buffering performed by the web browser before the audio starts. This process may take about 20 seconds or more for some browsers. Another important condition is that the connection bandwidth should be high enough; otherwise the audio will skip or become choppy.
DB45 How to: I forgot the master password for the DEVA Device Manager Software, what should I do?
If due to any reason you have forgotten your Master Password, contact us at support@devabroadcast.com for detailed instructions on the reset procedure.
DB45 How to: I have forgotten my password for the WEB Interface. What should I do?
If due to any reason you have forgotten your WEB Interface password, in order for a new password to be assigned to the device, the unit should be returned to its factory defaults.
The procedure is performed via the reset button placed on the rear panel of the device. To ensure that the procedure has been properly completed, please follow the instructions below:
- Unplug the device from the power supply;
- Press and hold the reset button;
- While pressing the button, connect the device to the power supply again;
- Wait for a few seconds, until the Power LED starts blinking;
- Release the reset button;
- The device should be returned to its factory defaults.
DB45 How to: How can I switch between %/KHz (RDS/RBDS Mode)?
The mode could be changed via the WEB Interface only. The menu path for both the Receiver and Streamer WEB Interfaces is: Settings > Tuner > section “RDS/RBDS Mode”.
How to reset the DB45 to its factory defaults without having access to the WEB Interface?
To start a Hardware Reset, disconnect the power supply cable from the unit. Then locate the RESET button on Rear panel (labeled in red on the picture), press and hold it.
Afterwards, connect the power supply cable to the unit and keep the RESET button pressed until the POWER led starts blinking. Release the RESET button and wait for DB45 to reboot with the factory default settings.